VW Vortex - Volkswagen Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-16 of 16 Results
  1. Golf III/Jetta III Parts
    Hi, looking to buy a pre-‘96 ABA intake boot, it will have two ports instead of only one on the OBD2 boots. Will pick up locally if in the central GA/ATL regions, otherwise I will pay shipping from any part of the U.S.
    $65 USD
  2. Golf III & Jetta III
    1994 Mk3 Jetta 2.0 ABA USDM. Not Sure which pairs of cables go to which terminal and if the positive cable is supposed to be cut and wired to the cooling fan module. 1st pair is a brown&white cable and Orange cable 2nd pair is a solid red cable and red&white cable And im not sure if the...
  3. Golf II & Jetta II
    I Recently finished my year-long Jetta build, and it's wonderful. It drives great and has ice cold AC. Perfect. A few little irritations, but all around, I'm over the moon about it. It's just an ABA with AC, PS, a 12" sub and wolfsburg edition interior. The paint isn't perfect, but she's a...
  4. Golf II & Jetta II
    The original builder is 6speed16v I believe. And I’m happy to say I want to bring this car back to its former glory. Car is ABA swapped with 98 TDI trans, mk3 cluster as well. It’s got a lot of work needed but ittl be worth it in the end!
  5. 2.0 Liter Engine Forum
    I am confused on how to wire the ignition coil part number: 6N0905104 to stand alone ecu. The stand alone ecu I am using is speeduino but Id imagine the wiring is the same for any stand alone ecu. The ignition coil is a 3 pin. Any help or pointing me to a wiring diagram or aba stand alone guide...
  6. Golf I & Jetta I
    Just as the title states not running an 02 sensor on my mk1 aba swap car runs perfectly fine however I would assume rich without sensor, any huge downsides to not running one?
    aba
  7. Golf III & Jetta III
    My long-term project mk3.5 Cabrio is finally getting a VR6. I've known I wanted to do this swap for ages and have been researching/planning how to do it for at least 4 or 5 years. I had the absolutely perfect donor car come along, a very lightly crashed 2 owner 1997 Jetta GLX 5 speed in...
  8. Golf I & Jetta I
    I am planning on swapping a aba into my mk1 jetta coupe does anyone know of any aftermarket wiring harnesses that are a easy plug and play type thing?
  9. Golf III & Jetta III
    I’ll be replacing the oil Pan gasket, valve cover gasket, filter housing gasket, oil cooler ring, rear main seal, and all manifold gaskets. I’ll also be shooting some WD40 into the cylinders before I turn it over by hand. Also going to inspect and clean oil pump when I pull Pan off. I don’t plan...
  10. Golf III/Jetta III Cars
    Looking for a decently clean mk3 somewhere around the Boise/Utah/Eastern Oregon area Must be a manual No real preference on color Must be an ABA I regrettably sold my old ABA MK3 I turbocharged and would really love another.
  11. Golf I & Jetta I
    Hi all. Just finished my ABA swap w 4 speed 020 and I’d like a way to see my fuel economy. I’m not slamming the gas, I get to 4th gear ASAP, but I’m only getting around 27mpg, which is a bit pathetic for a 2.0 in a little MK1 body, when it gets 30+ in a MK3 body. How do I go about wiring in an...
  12. Golf III & Jetta III
    Hi all. Finally finishing up the ABA swap into my ‘76 Mk1 this weekend, and I’m still not firing after everything being checked. It’s a 1995 vw golf engine, with a 4 speed 020 transmission I had rebuilt. New clutch, same flywheel just resurfaced. Ilined my camshaft sprocket up to the OT arrow...
  13. The Volkswagen Lounge
    Hey there. This is my first post and i would appreciate any input. I'm trying to figure out what to do about this car. The last owner couldn't get it to run at all. I purchased it and fiddled around with it couple of days. I eventually got it running but it died down the road. I had reset the...
  14. Golf III/Jetta III Parts
    All I need to finish up my setup is the manifold and intercollegiate piping I have everything else left over from previous build could pay shipping but if you’re in the Midwest meeting up would be easiest thanks in advance!!!
  15. 2.0 Liter Engine Forum
    Good morning all. I've created this poll to gauge interest in possibly creating a pre-order for our upcoming turbo kit. We aim to keep this kit as flexible as possible so with that some people might not need/want the tuning offered with it and prefer to go another route. That may be standalone...
1-16 of 16 Results
Top